diff --git a/docs/Makefile b/docs/Makefile
new file mode 100644
index 0000000..c715218
--- /dev/null
+++ b/docs/Makefile
@@ -0,0 +1,37 @@
+
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+#      http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+# Minimal makefile for Sphinx documentation
+#
+
+# You can set these variables from the command line, and also
+# from the environment for the first two.
+SPHINXOPTS    ?=
+SPHINXBUILD   ?= sphinx-build
+SOURCEDIR     = source
+BUILDDIR      = build
+
+# Put it first so that "make" without argument is like "make help".
+help:
+	@$(SPHINXBUILD) -M help "$(SOURCEDIR)" "$(BUILDDIR)" $(SPHINXOPTS) $(O)
+
+.PHONY: help Makefile
+
+# Catch-all target: route all unknown targets to Sphinx using the new
+# "make mode" option.  $(O) is meant as a shortcut for $(SPHINXOPTS).
+%: Makefile
+	@$(SPHINXBUILD) -M $@ "$(SOURCEDIR)" "$(BUILDDIR)" $(SPHINXOPTS) $(O)
+
diff --git a/docs/environment.yml b/docs/environment.yml
new file mode 100644
index 0000000..2bddf94
--- /dev/null
+++ b/docs/environment.yml
@@ -0,0 +1,23 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+#      http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+name: caravel-docs
+channels:
+- defaults
+dependencies:
+- python>=3.8
+- pip:
+  - -r file:requirements.txt
diff --git a/docs/requirements.txt b/docs/requirements.txt
new file mode 100644
index 0000000..f5c5383
--- /dev/null
+++ b/docs/requirements.txt
@@ -0,0 +1,6 @@
+git+https://github.com/SymbiFlow/sphinx_materialdesign_theme.git#egg=sphinx-symbiflow-theme
+
+docutils
+sphinx
+sphinx-autobuild
+sphinxcontrib-wavedrom
diff --git a/docs/source/conf.py b/docs/source/conf.py
new file mode 100644
index 0000000..f960f13
--- /dev/null
+++ b/docs/source/conf.py
@@ -0,0 +1,89 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+#      http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+# Configuration file for the Sphinx documentation builder.
+#
+# This file only contains a selection of the most common options. For a full
+# list see the documentation:
+# https://www.sphinx-doc.org/en/master/usage/configuration.html
+
+# -- Path setup --------------------------------------------------------------
+
+# If extensions (or modules to document with autodoc) are in another directory,
+# add these directories to sys.path here. If the directory is relative to the
+# documentation root, use os.path.abspath to make it absolute, like shown here.
+#
+# import os
+# import sys
+# sys.path.insert(0, os.path.abspath('.'))
+
+
+# -- Project information -----------------------------------------------------
+
+project = 'CIIC Harness'
+copyright = '2020, efabless'
+author = 'efabless'
+
+
+# -- General configuration ---------------------------------------------------
+
+# Add any Sphinx extension module names here, as strings. They can be
+# extensions coming with Sphinx (named 'sphinx.ext.*') or your custom
+# ones.
+extensions = [
+  'sphinxcontrib.wavedrom',
+  'sphinx.ext.mathjax',
+  'sphinx.ext.todo'
+]
+
+# Add any paths that contain templates here, relative to this directory.
+templates_path = ['_templates']
+
+# List of patterns, relative to source directory, that match files and
+# directories to ignore when looking for source files.
+# This pattern also affects html_static_path and html_extra_path.
+exclude_patterns = [
+    'build',
+    'Thumbs.db',
+    # Files included in other rst files.
+    'introduction.rst',
+]
+
+
+# -- Options for HTML output -------------------------------------------------
+"""
+html_theme_options = {
+    'header_links' : [
+        ("Home", 'index', False, 'home'),
+        ("GitHub", "https://github.com/efabless/caravel", True, 'code'),
+    ],
+    'hide_symbiflow_links': True,
+    'license_url' : 'https://www.apache.org/licenses/LICENSE-2.0',
+}
+"""
+# The theme to use for HTML and HTML Help pages.  See the documentation for
+# a list of builtin themes.
+#
+html_theme = 'sphinx_rtd_theme'
+
+# Add any paths that contain custom static files (such as style sheets) here,
+# relative to this directory. They are copied after the builtin static files,
+# so a file named "default.css" will overwrite the builtin "default.css".
+html_static_path = ['_static']
+
+todo_include_todos = False
+
+numfig = True
diff --git a/docs/source/index.rst b/docs/source/index.rst
new file mode 100644
index 0000000..32047d3
--- /dev/null
+++ b/docs/source/index.rst
@@ -0,0 +1,335 @@
+.. raw:: html
+
+   <!---
+   # SPDX-FileCopyrightText: 2020 Efabless Corporation
+   #
+   # Licensed under the Apache License, Version 2.0 (the "License");
+   # you may not use this file except in compliance with the License.
+   # You may obtain a copy of the License at
+   #
+   #      http://www.apache.org/licenses/LICENSE-2.0
+   #
+   # Unless required by applicable law or agreed to in writing, software
+   # distributed under the License is distributed on an "AS IS" BASIS,
+   # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+   # See the License for the specific language governing permissions and
+   # limitations under the License.
+   #
+   # SPDX-License-Identifier: Apache-2.0
+   -->
+
+Caravel Analog User Project
+===========================
+
+|License| |User CI| |Caravan Build|
+
+Table of contents
+=================
+
+-  `Overview <#overview>`__
+-  `Install Caravel <#install-caravel>`__
+-  `Caravel Integration <#caravel-integration>`__
+
+   - `User Project: Power on Reset <#user-project-power-on-reset>`_
+   -  `Verilog Integration <#verilog-integration>`__
+   
+-  `Running Full Chip Simulation <#running-full-chip-simulation>`__
+-  `Analog Design Flow <#analog-design-flow>`__
+- `Other Miscellaneous Targets <#other-miscellaneous-targets>`_
+-  `Checklist for Open-MPW
+   Submission <#checklist-for-open-mpw-submission>`__
+   
+Overview
+========
+
+This repo contains a sample user project that utilizes the caravan chip (analog version of `caravel <https://github.com/efabless/caravel.git>`__) user space. The user project is a simple power-on-reset that showcases how to make use of caravan's user space utilities like IO pads, logic analyzer probes, and wishbone port. The repo also demonstrates the recommended structure for the open-mpw **analog** projects.
+
+Install Caravel
+===============
+
+To setup caravel, run the following:
+
+.. code:: bash
+
+    # By default, CARAVEL_ROOT is set to $(pwd)/caravel
+    # If you want to install caravel at a different location, run "export CARAVEL_ROOT=<caravel-path>"
+    # Disable submodule installation if needed by, run "export SUBMODULE=0"
+    
+    git clone https://github.com/efabless/caravel_user_project_analog.git
+    cd caravel_user_project_analog
+    make install
+
+To update the installed caravel to the latest, run:
+
+.. code:: bash
+
+     make update_caravel
+
+To remove caravel, run
+
+.. code:: bash
+
+    make uninstall
+
+By default
+`caravel-lite <https://github.com/efabless/caravel-lite.git>`__ is
+installed. To install the full version of caravel, run this prior to
+calling make install.
+
+.. code:: bash
+
+    export CARAVEL_LITE=0
+ 
+Caravel Integration
+=====================
+
+
+User Project: Power on Reset
+----------------------------
+
+This is an example user analog project which breaks out the power-on-reset
+circuit used by the management SoC for power-up behavior so that the circuit
+input and output can be independently controlled and measured.
+
+The power-on-reset circuit itself is a simple, non-temperature-compensated
+analog delay calibrated to 15ms under nominal conditions, with a Schmitt
+trigger inverter to provide hysteresis around the trigger point to provide
+a clean output reset signal. 
+
+The circuit provides a single high-voltage (3.3V domain) sense-inverted reset
+signal "porb_h" and complementary low-voltage (1.8V domain) reset signals
+"por_l" and "porb_l".
+
+The only input to the circuit is the 3.3V domain power supply itself.
+
+
+Verilog Integration
+-------------------
+
+You need to create a wrapper around your macro that adheres to the
+template at
+`user\_analog_project\_wrapper <https://github.com/efabless/caravel/blob/master/verilog/rtl/__user_analog_project_wrapper.v>`__.
+The wrapper top module must be named ``user_analog_project_wrapper`` and must
+have the same input and output ports as the analog wrapper template. The wrapper gives access to the
+user space utilities provided by caravel like IO ports, logic analyzer
+probes, and wishbone bus connection to the management SoC.
+
+The verilog modules instantiated in the wrapper module should represent
+the analog project;  they need not be more than empty blocks, but it is
+encouraged to write a simple behavioral description of the analog circuit
+in standard verilog, using real-valued wires when necessary.  This allows
+the whole system to be run in a verilog testbench and verify the connectivity
+to the padframe and management SoC, even if the testbench C code does nothing
+more than set the mode of each GPIO pin.  The example top-level verilog code
+emulates the behavior of the power-on-reset delay after applying a valid
+power supply to the circuit.
+
+
+Building the PDK 
+================
+
+You have two options for building the pdk: 
+
+- Build the pdk natively. 
+
+Make sure you have `Magic VLSI Layout Tool <http://opencircuitdesign.com/magic/index.html>`__   `version 8.3.160 <https://github.com/RTimothyEdwards/magic/tree/8.3.160>`__ installed on your machine before building the pdk. 
+
+.. code:: bash
+
+    # set PDK_ROOT to the path you wish to use for the pdk
+    export PDK_ROOT=<pdk-installation-path>
+
+    # you can optionally specify skywater-pdk and open-pdks commit used
+    # by setting and exporting SKYWATER_COMMIT and OPEN_PDKS_COMMIT
+    # if you do not set them, they default to the last verfied commits tested for this project
+
+    make pdk
+
+- Build the pdk using openlane's docker image which has magic installed. 
+
+.. code:: bash
+
+    # set PDK_ROOT to the path you wish to use for the pdk
+    export PDK_ROOT=<pdk-installation-path>
+
+    # you can optionally specify skywater-pdk and open-pdks commit used
+    # by setting and exporting SKYWATER_COMMIT and OPEN_PDKS_COMMIT
+    # if you do not set them, they default to the last verfied commits tested for this project
+
+    make pdk-nonnative
+
+Running Full Chip Simulation
+============================
+
+First, you will need to install the simulation environment, by
+
+.. code:: bash
+
+    make simenv
+
+This will pull a docker image with the needed tools installed.
+
+To install the simulation environment locally, refer to `README <https://github.com/efabless/caravel_user_project_analog/blob/main/verilog/dv/README.md>`__
+
+Then, run the RTL and GL simulation by
+
+.. code:: bash
+
+    export PDK_ROOT=<pdk-installation-path>
+    export CARAVEL_ROOT=$(pwd)/caravel
+    # specify simulation mode: RTL/GL
+    export SIM=RTL
+    # Run the mprj_por testbench, make verify-mprj_por
+    make verify-<testbench-name>
+
+The verilog test-benches are under this directory
+`verilog/dv <https://github.com/efabless/caravel_user_project_analog/tree/main/verilog/dv>`__.
+
+
+Analog Design Flow
+===================
+
+The example project uses a very simple analog design flow with schematics
+made with xschem, simulation done using ngspice, layout done with magic,
+and LVS verification done with netgen.  Sources for the power-on-reset
+circuit are in the "xschem/" directory, which also includes a schematic
+representing the wrapper with all of its ports, for use in a testbench
+circuit.  There are several testbenches in the example, starting from
+tests of the component devices to a full test of the completed project
+inside the wrapper.
+
+There is no automation in this project;  the schematic and layout were
+done by hand, including both the power-on-reset block and the power and
+signal routing to the pins on the wrapper.
+
+The power-on-reset circuit itself is simple and is not compensated for
+temperature or voltage variation.  When the power supply reaches a
+sufficient level, the voltage divider sets the gate voltage on an nFET
+device to draw a current of nominally 240nA.  The testbench
+"threshold_test_tb.spice" does a DC sweep to find the gate voltage that
+produces this value.   Next, a cascaded current mirror divides down the
+current by a factor of (roughly) 400.  The testbench current_test.spice
+checks the current division value.  Finally, the output ~600pA from the
+end of the current mirror is accumulated on a capacitor until the value
+trips the input of the 3.3V Schmitt trigger buffer from the
+sky130_fd_sd_hvl library.  The capacitor is sized to peg the nominal
+time to trigger at 15ms.  The schematic "example_por_tb.sch" sets up
+the testbench for this timing test.
+
+The output of the Schmitt trigger buffer becomes the high-voltage
+output, and is input to a standard buffer and inverter used as
+level shifters from the 3.3V domain to the 1.8V domain, producing
+complementary low-voltage outputs.
+
+The user project is formed from two power-on-reset circuits, one of
+which is connected to the user area VDDA1 power supply, and the other
+of which is connected to one of the analog I/O pads, used as a power
+supply input and connected to its voltage ESD clamp circuit.  The
+3.3V domain outputs are connected directly to GPIO pads through the
+ESD (150 ohm series) connection.  The 1.8V domain outputs are connected
+to GPIO pads through the usual I/O connections, with the corresponding
+user output enable (sense inverted) held low to keep the output always
+active.
+
+The C code testbench is in "verilog/dv/mprj_por/mprj_por.c" and only
+sets the GPIO pins used to the correct state (user output function).
+The POR circuit outputs are monitored by the testbench verilog file
+"mprj_por_tb.v" which will fail if the connections are wrong or if
+the behavioral POR verilog does not work as intended.
+
+Note that to properly test this circuit, the GPIO pins have to be
+configured for output to be seen and measured, implying that the
+management SoC power supply must be stable and the C program running
+off of the SPI flash before the user area power supplies are raised.
+
+**NOTE**
+
+   When running spice extraction on the user_analog_project_wrapper layout, it is recommended to use `ext2spice short resistor`. 
+   This is to preserve all the different port names in the extracted netlist. In case you have two ports that are electrically shorted
+   in the layout, the `short resistor` option will tell magic not to merge the two shorted ports instead it adds zero-ohm ideal resistors 
+   between the net names so that they can be kept as separate nets. 
+   
+
+Running Open-MPW Precheck Locally
+=================================
+
+You can install the precheck by running 
+
+.. code:: bash
+
+   # By default, this install the precheck in your home directory
+   # To change the installtion path, run "export PRECHECK_ROOT=<precheck installation path>" 
+   make precheck
+
+This will clone the precheck repo and pull the latest precheck docker image. 
+
+
+Then, you can run the precheck by running
+Specify CARAVEL_ROOT before running any of the following, 
+
+.. code:: bash
+
+   # export CARAVEL_ROOT=$(pwd)/caravel 
+   export CARAVEL_ROOT=<path-to-caravel>
+   make run-precheck
+
+This will run all the precheck checks on your project and will retain the logs under the ``checks`` directory.
+
+Other Miscellaneous Targets
+============================
+
+The makefile provides a number of useful that targets that can run compress, uncompress, and run XOR checks on your design. 
+
+Compress gds files and any file larger than 100MB (GH file size limit), 
+
+.. code:: bash
+
+   make compress
+
+Uncompress files, 
+
+.. code:: bash
+
+   make uncompress
+
+
+Specify ``CARAVEL_ROOT`` before running any of the following, 
+
+.. code:: bash
+
+   # export CARAVEL_ROOT=$(pwd)/caravel 
+   export CARAVEL_ROOT=<path-to-caravel>
+   
+Run XOR check, 
+
+.. code:: bash
+
+   make xor-analog-wrapper
+
+Checklist for Open-MPW Submission
+=================================
+
+
+|:heavy_check_mark:| The project repo adheres to the same directory structure in this repo.
+   
+|:heavy_check_mark:| The project repo contain info.yaml at the project root.
+
+|:heavy_check_mark:| Top level macro is named ``user_analog_project_wrapper``.
+
+|:heavy_check_mark:| Full Chip Simulation passes for RTL and GL (gate-level)
+
+|:heavy_check_mark:| The hardened Macros are LVS and DRC clean
+
+|:heavy_check_mark:| The ``user_analog_project_wrapper`` adheres to empty wrapper template  order specified at  `user_analog_project_wrapper_empty <https://github.com/efabless/caravel/blob/master/mag/user_analog_project_wrapper_empty.mag>`__
+
+|:heavy_check_mark:| XOR check passes with zero total difference.
+
+|:heavy_check_mark:| Open-MPW-Precheck tool runs successfully. 
+
+
+.. |License| image:: https://img.shields.io/badge/License-Apache%202.0-blue.svg
+   :target: https://opensource.org/licenses/Apache-2.0
+.. |User CI| image:: https://github.com/efabless/caravel_user_project_analog/actions/workflows/user_project_ci.yml/badge.svg
+   :target: https://github.com/efabless/caravel_user_project_analog/actions/workflows/user_project_ci.yml
+.. |Caravan Build| image:: https://github.com/efabless/caravel_user_project_analog/actions/workflows/caravan_build.yml/badge.svg
+   :target: https://github.com/efabless/caravel_user_project_analog/actions/workflows/caravan_build.yml