diff --git a/verilog/rtl/user_proj_example.v b/verilog/rtl/user_proj_example.v
deleted file mode 100644
index eae4ab1..0000000
--- a/verilog/rtl/user_proj_example.v
+++ /dev/null
@@ -1,95 +0,0 @@
-// SPDX-FileCopyrightText: 2020 Efabless Corporation
-//
-// Licensed under the Apache License, Version 2.0 (the "License");
-// you may not use this file except in compliance with the License.
-// You may obtain a copy of the License at
-//
-//      http://www.apache.org/licenses/LICENSE-2.0
-//
-// Unless required by applicable law or agreed to in writing, software
-// distributed under the License is distributed on an "AS IS" BASIS,
-// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-// See the License for the specific language governing permissions and
-// limitations under the License.
-// SPDX-License-Identifier: Apache-2.0
-
-`default_nettype none
-/*
- *-------------------------------------------------------------
- *
- * user_proj_example
- *
- * This is an example of a (trivially simple) user project,
- * showing how the user project can connect to the logic
- * analyzer, the wishbone bus, and the I/O pads.
- *
- * This project generates an integer count, which is output
- * on the user area GPIO pads (digital output only).  The
- * wishbone connection allows the project to be controlled
- * (start and stop) from the management SoC program.
- *
- * See the testbenches in directory "mprj_counter" for the
- * example programs that drive this user project.  The three
- * testbenches are "io_ports", "la_test1", and "la_test2".
- *
- *-------------------------------------------------------------
- */
-
-module user_proj_example #(
-    parameter BITS = 32
-)(
-`ifdef USE_POWER_PINS
-    inout vdda1,	// User area 1 3.3V supply
-    inout vdda2,	// User area 2 3.3V supply
-    inout vssa1,	// User area 1 analog ground
-    inout vssa2,	// User area 2 analog ground
-    inout vccd1,	// User area 1 1.8V supply
-    inout vccd2,	// User area 2 1.8v supply
-    inout vssd1,	// User area 1 digital ground
-    inout vssd2,	// User area 2 digital ground
-`endif
-
-
-    // IOs
-    input in,
-    inout out
-);
-    
-    avsdbgp_3v3_sky130_v2 #(
-        .BITS(BITS)
-    ) avsdbgp_3v3_sky130_v2 (
-        .EN(in),
-        .VBGP(out)
-        );
-
-endmodule
-
-module avsdbgp_3v3_sky130_v2 #(
-    parameter BITS = 32
-)(
-
-  input EN,
-  output VBGP
-
-);
-
-  reg real VBGP;
-
-  initial begin
-     if (EN == 1'b1) begin
-        VBGP <= 1.19;
-     end else begin
-        VBGP <= 0.0;
-     end
-  end
-
-  always @(EN) begin
-     if (EN == 1'b1) begin
-        VBGP <= 1.19;
-     end else begin
-        VBGP <= 0.0;
-     end
-  end
-
-endmodule
-`default_nettype wire