| /* | |
| * SPDX-FileCopyrightText: 2020 Efabless Corporation | |
| * | |
| * Licensed under the Apache License, Version 2.0 (the "License"); | |
| * you may not use this file except in compliance with the License. | |
| * You may obtain a copy of the License at | |
| * | |
| * http://www.apache.org/licenses/LICENSE-2.0 | |
| * | |
| * Unless required by applicable law or agreed to in writing, software | |
| * distributed under the License is distributed on an "AS IS" BASIS, | |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |
| * See the License for the specific language governing permissions and | |
| * limitations under the License. | |
| * SPDX-License-Identifier: Apache-2.0 | |
| */ | |
| // This include is relative to $CARAVEL_PATH (see Makefile) | |
| #include "verilog/dv/caravel/defs.h" | |
| #include "verilog/dv/caravel/stub.c" | |
| /* | |
| Wishbone Test: | |
| - Configures MPRJ lower 8-IO pins as outputs | |
| - Checks counter value through the wishbone port | |
| */ | |
| int i = 0; | |
| int clk = 0; | |
| void main() | |
| { | |
| /* | |
| IO Control Registers | |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | | |
| | 3-bits | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | | |
| Output: 0000_0110_0000_1110 (0x1808) = GPIO_MODE_USER_STD_OUTPUT | |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | | |
| | 110 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | | |
| Input: 0000_0001_0000_1111 (0x0402) = GPIO_MODE_USER_STD_INPUT_NOPULL | |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | | |
| | 001 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | | |
| */ | |
| /* Set up the housekeeping SPI to be connected internally so */ | |
| /* that external pin changes don't affect it. */ | |
| reg_spimaster_config = 0xa002; // Enable, prescaler = 2, | |
| // connect to housekeeping SPI | |
| // Connect the housekeeping SPI to the SPI master | |
| // so that the CSB line is not left floating. This allows | |
| // all of the GPIO pins to be used for user functions. | |
| reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT; | |
| /* Apply configuration */ | |
| reg_mprj_xfer = 1; | |
| while (reg_mprj_xfer == 1); | |
| reg_la2_oenb = reg_la2_iena = 0xFFFFFFFF; // [95:64] | |
| // Flag start of the test | |
| reg_mprj_datal = 0xAB600000; | |
| reg_mprj_slave = 0x00002710; | |
| if (reg_mprj_slave == 0x274F) { | |
| reg_mprj_datal = 0xAB610000; | |
| } else { | |
| reg_mprj_datal = 0xAB600000; | |
| } | |
| } |