| // SPDX-FileCopyrightText: 2020 Efabless Corporation | |
| // | |
| // Licensed under the Apache License, Version 2.0 (the "License"); | |
| // you may not use this file except in compliance with the License. | |
| // You may obtain a copy of the License at | |
| // | |
| // http://www.apache.org/licenses/LICENSE-2.0 | |
| // | |
| // Unless required by applicable law or agreed to in writing, software | |
| // distributed under the License is distributed on an "AS IS" BASIS, | |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |
| // See the License for the specific language governing permissions and | |
| // limitations under the License. | |
| // SPDX-License-Identifier: Apache-2.0 | |
| `default_nettype none | |
| `timescale 1 ns / 1 ps | |
| `include "simpleuart.v" | |
| module uart_wb_tb; | |
| reg wb_clk_i; | |
| reg wb_rst_i; | |
| reg wb_stb_i; | |
| reg wb_cyc_i; | |
| reg wb_we_i; | |
| reg [3:0] wb_sel_i; | |
| reg [31:0] wb_adr_i; | |
| reg [31:0] wb_dat_i; | |
| wire wb_ack_o; | |
| wire [31:0] wb_dat_o; | |
| wire tbuart_rx; | |
| wire ser_rx; | |
| initial begin | |
| wb_clk_i = 0; | |
| wb_rst_i = 0; | |
| wb_stb_i = 0; | |
| wb_we_i = 0; | |
| wb_cyc_i = 0; | |
| wb_adr_i = 0; | |
| wb_dat_i = 0; | |
| wb_sel_i = 0; | |
| end | |
| always #1 wb_clk_i = ~wb_clk_i; | |
| initial begin | |
| $dumpfile("uart_wb_tb.vcd"); | |
| $dumpvars(0, uart_wb_tb); | |
| repeat (500) begin | |
| repeat (10000) @(posedge wb_clk_i); | |
| end | |
| $display("%c[1;31m",27); | |
| $display("Monitor: Timeout, Test UART Failed"); | |
| $display("%c[0m",27); | |
| $finish; | |
| end | |
| integer i; | |
| wire [31:0] div_reg_addr = uut.BASE_ADR | uut.CLK_DIV; | |
| wire [31:0] div_reg_data = 32'h FFFF_FFFF; | |
| wire [31:0] dat_reg_addr = uut.BASE_ADR | uut.DATA; | |
| wire [31:0] dat_reg_data = 32'h FFFF_FFFF; | |
| initial begin | |
| // Reset Operation | |
| wb_rst_i = 1; | |
| #2; | |
| wb_rst_i = 0; | |
| #2; | |
| // Write to div register | |
| write(div_reg_addr, div_reg_data); | |
| #2; | |
| read(div_reg_addr); | |
| if (wb_dat_o !== div_reg_data) begin | |
| $display("%c[1;31m",27); | |
| $display("Expected %0b, but Got %0b ", div_reg_data, wb_dat_o); | |
| $display("Monitor: Wishbone UART Failed"); | |
| $display("%c[0m",27); | |
| $finish; | |
| end | |
| #6; | |
| // Write Operation: writes to data register | |
| write(dat_reg_addr, dat_reg_data); | |
| #2; | |
| read(dat_reg_addr); | |
| if (wb_dat_o !== dat_reg_data) begin | |
| $display("%c[1;31m",27); | |
| $display("Expected %0b, but Got %0b ", dat_reg_data, wb_dat_o); | |
| $display("Monitor: Wishbone UART Failed"); | |
| $display("%c[0m",27); | |
| $finish; | |
| end | |
| $display("Success!"); | |
| $display("Monitor: Wishbone UART Passed"); | |
| $finish; | |
| end | |
| task write; | |
| input [32:0] addr; | |
| input [32:0] data; | |
| begin | |
| @(posedge wb_clk_i) begin | |
| wb_stb_i = 1; | |
| wb_cyc_i = 1; | |
| wb_sel_i = 4'hF; | |
| wb_we_i = 1; | |
| wb_adr_i = addr; | |
| wb_dat_i = data; | |
| $display("Write Cycle Started."); | |
| end | |
| #2; | |
| wb_we_i = 0; | |
| // Wait for an ACK | |
| wait(wb_ack_o == 1); | |
| #2; | |
| wb_cyc_i = 0; | |
| wb_stb_i = 0; | |
| $display("Write Cycle Ended."); | |
| end | |
| endtask | |
| task read; | |
| input [32:0] addr; | |
| begin | |
| @(posedge wb_clk_i) begin | |
| wb_stb_i = 1; | |
| wb_cyc_i = 1; | |
| wb_we_i = 0; | |
| wb_adr_i = addr; | |
| $display("Read Cycle Started."); | |
| end | |
| // Wait for an ACK | |
| wait(wb_ack_o == 1); | |
| #2; | |
| // wait(wb_ack_o == 0); | |
| wb_cyc_i = 0; | |
| wb_stb_i = 0; | |
| $display("Read Cycle Ended."); | |
| end | |
| endtask | |
| simpleuart_wb uut ( | |
| .wb_clk_i(wb_clk_i), | |
| .wb_rst_i(wb_rst_i), | |
| .wb_stb_i(wb_stb_i), | |
| .wb_cyc_i(wb_cyc_i), | |
| .wb_sel_i(wb_sel_i), | |
| .wb_we_i(wb_we_i), | |
| .wb_adr_i(wb_adr_i), | |
| .wb_dat_i(wb_dat_i), | |
| .wb_ack_o(wb_ack_o), | |
| .wb_dat_o(wb_dat_o), | |
| .ser_tx(tbuart_rx), | |
| .ser_rx(ser_rx) | |
| ); | |
| endmodule |