// To be completely honest I'm not really sure how the connection block works, so someone should probably look over this

module baked_connection_block #(
  parameter WS = 4,
  parameter WD = 8,
  parameter WG = 0,
  parameter CLBIN = 10,
  parameter CLBIN0 = 10,
  parameter CLBIN1 = 10,
  parameter CLBOUT = 5,
  parameter CLBOUT0 = 5,
  parameter CLBOUT1 = 5,
  parameter CARRY = 1,
  parameter CLBOS = 2,
  parameter CLBOS_BIAS = 0,
  parameter CLBOD = 2,
  parameter CLBOD_BIAS = 0,
  parameter CLBX = 1
)(
  // Common
  input wire clk,
  input wire rst,

  // Confiuration Signals:

  input wire cen,

  // Config set input (from tile module)
  input wire set_in,

  // Config shift input (from tile module)
  input wire shift_in,
  // Config shift output (to tile module)
  output wire shift_out,

  // Single Wires
  inout [WS-1:0] single0, single1,
  // Double Wires
  inout [WD-1:0] double0, double1,
  // Global Wires
  inout [WG-1:0] global,

  input [CLBOUT-1:0] clb0_output,
  input [CLBOUT-1:0] clb1_output,
  input [CARRY-1:0]  clb0_cout,
  input [CARRY-1:0]  clb1_cout,
  output [CLBIN-1:0] clb0_input,
  output [CLBIN-1:0] clb1_input,
  output [CARRY-1:0] clb0_cin,
  output [CARRY-1:0] clb1_cin
);

localparam SWITCH_PER_IN0 = WS + WD + WG + CLBX * CLBOUT1;
localparam SWITCH_PER_IN1 = WS + WD + WG + CLBX * CLBOUT0;
localparam SWITCH_PER_OUT = CLBOS + CLBOD;

localparam CB_CONF_WIDTH = CLBIN0*SWITCH_PER_IN0+CLBOUT0*SWITCH_PER_OUT+CLBIN1*SWITCH_PER_IN1+CLBOUT1*SWITCH_PER_OUT;

wire [CB_CONF_WIDTH-1:0] cb_conf_bus;

reg [CB_CONF_WIDTH-1:0] cb_conf_regs;

always @(clk) begin
  if (set_in) begin
    cb_conf_regs <= cb_conf_bus;
  end
end

connection_block #(
  .WS(WS),
  .WD(WD),
  .WG(WG),
  .CLBIN(CLBIN),
  .CLBIN0(CLBIN0),
  .CLBIN1(CLBIN1),
  .CLBOUT(CLBOUT),
  .CLBOUT0(CLBOUT0),
  .CLBOUT1(CLBOUT1),
  .CARRY(CARRY),
  .CLBOS(CLBOS),
  .CLBOS_BIAS(CLBOS_BIAS),
  .CLBOD(CLBOD),
  .CLBOD_BIAS(CLBOD_BIAS),
  .CLBX(CLBX)
) connectaroni (
   .single0(single0),
   .single1(single1),
   .double0(double0),
   .double1(double1),
   .global(global),
   .clb0_output(clb0_output),
   .clb1_output(clb1_output),
   .clb0_input(clb0_input),
   .clb1_input(clb1_input),
   .clb1_cout(clb1_cout),
   .clb0_cin(clb0_cin),
   .clb1_cin(clb1_cin),
   .c(cb_conf_regs)
 );

// OH GREAT ABC9 WORK THY OPTIMIZATIONS VERILY
config_tile #(
  .COMB_N(CB_CONF_WIDTH),
  .MEM_N(0)
) configuroni (
  .clk(clk),
  .rst(rst),

  .shift_enable(cen & (~set_in)),
  .shift_in_hard(shift_in),
  .shift_in_soft(shift_in),
  .shift_out(shift_out),

  .set_hard(set_in),
  .set_soft(set_in),

  .comb_config(cb_conf_bus),
  .comb_set(),

  .mem_config(),
  .mem_set()
);

endmodule