| /* |
| * SPDX-FileCopyrightText: 2020 Efabless Corporation |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include "../../defs.h" |
| |
| /* |
| IO Test: |
| - Configures MPRJ lower 8-IO pins as outputs |
| - Observes counter value through the MPRJ lower 8 IO pins (in the testbench) |
| */ |
| |
| void main() |
| { |
| /* |
| IO Control Registers |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | |
| | 3-bits | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | |
| |
| Output: 0000_0110_0000_1110 (0x1808) = GPIO_MODE_USER_STD_OUTPUT |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | |
| | 110 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | |
| |
| |
| Input: 0000_0001_0000_1111 (0x0402) = GPIO_MODE_USER_STD_INPUT_NOPULL |
| | DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN | |
| | 001 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | |
| |
| */ |
| |
| /* Set up the housekeeping SPI to be connected internally so */ |
| /* that external pin changes don't affect it. */ |
| |
| reg_spimaster_config = 0xa002; // Enable, prescaler = 2, |
| // connect to housekeeping SPI |
| |
| // Connect the housekeeping SPI to the SPI master |
| // so that the CSB line is not left floating. This allows |
| // all of the GPIO pins to be used for user functions. |
| |
| // Configure lower 8-IOs as user output |
| // Observe counter value in the testbench |
| reg_mprj_io_0 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_1 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_2 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_3 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_4 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_5 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_6 = GPIO_MODE_USER_STD_OUTPUT; |
| reg_mprj_io_7 = GPIO_MODE_USER_STD_OUTPUT; |
| |
| /* Apply configuration */ |
| reg_mprj_xfer = 1; |
| while (reg_mprj_xfer == 1); |
| |
| } |
| |