// SPDX-FileCopyrightText: Copyright (C) 2017  Clifford Wolf <clifford@clifford.at>
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *  StriVe - A full example SoC using PicoRV32 in SkyWater s8
 *
 *  Copyright (C) 2017  Clifford Wolf <clifford@clifford.at>
 *  Copyright (C) 2018  Tim Edwards <tim@efabless.com>
 *
 *  Permission to use, copy, modify, and/or distribute this software for any
 *  purpose with or without fee is hereby granted, provided that the above
 *  copyright notice and this permission notice appear in all copies.
 *
 *  THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
 *  WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
 *  MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
 *  ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
 *  WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
 *  ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
 *  OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
 *
 */

`timescale 1 ns / 1 ps

`define GL

`include "caravel.v"
`include "spiflash.v"

module mem_tb;
	reg clock;
	reg RSTB;
	reg power1, power2;

	wire gpio;
        wire [15:0] checkbits;
	wire [37:0] mprj_io;
	wire flash_csb;
	wire flash_clk;
	wire flash_io0;
	wire flash_io1;

	assign checkbits = mprj_io[31:16];

	// External clock is used by default.  Make this artificially fast for the
	// simulation.  Normally this would be a slow clock and the digital PLL
	// would be the fast clock.

	always #10 clock <= (clock === 1'b0);

	initial begin
		clock = 0;
	end

	initial begin
		$dumpfile("mem.vcd");
		$dumpvars(0, mem_tb);

		// Repeat cycles of 1000 clock edges as needed to complete testbench
		repeat (100) begin
			repeat (1000) @(posedge clock);
			//$display("+1000 cycles");
		end
		$display("%c[1;31m",27);
		$display ("Monitor: Timeout, Test MEM (GL) Failed");
		$display("%c[0m",27);
		$finish;
	end

	initial begin
		RSTB <= 1'b0;
		#1000;
		RSTB <= 1'b1;	    // Release reset
		#2000;
	end

	initial begin		// Power-up sequence
		power1 <= 1'b0;
		power2 <= 1'b0;
		#200;
		power1 <= 1'b1;
		#200;
		power2 <= 1'b1;
	end

	always @(checkbits) begin
		if(checkbits == 16'hA040) begin
			$display("Mem Test (word rw) started");
		end
		else if(checkbits == 16'hAB40) begin
			$display("%c[1;31m",27);
			$display("Monitor: Test MEM (GL) [word rw] failed");
			$display("%c[0m",27);
			$finish;
		end
		else if(checkbits == 16'hAB41) begin
			$display("Monitor: Test MEM (GL) [word rw]  passed");
		end
		else if(checkbits == 16'hA020) begin
			$display("Mem Test (short rw) started");
		end
		else if(checkbits == 16'hAB20) begin
			$display("%c[1;31m",27);
			$display("Monitor: Test MEM (GL) [short rw] failed");
			$display("%c[0m",27);
			$finish;
		end
		else if(checkbits == 16'hAB21) begin
			$display("Monitor: Test MEM (GL) [short rw]  passed");
		end
		else if(checkbits == 16'hA010) begin
			$display("Mem Test (byte rw) started");
		end
		else if(checkbits == 16'hAB10) begin
			$display("%c[1;31m",27);
			$display("Monitor: Test MEM (GL) [byte rw] failed");
			$display("%c[0m",27);
			$finish;
		end
		else if(checkbits == 16'hAB11) begin
			$display("Monitor: Test MEM (GL) [byte rw] passed");
			$finish;
		end

	end

	wire VDD3V3;
	wire VDD1V8;
	wire VSS;

	assign VSS = 1'b0;
	assign VDD3V3 = power1;
	assign VDD1V8 = power2;

	caravel uut (
		.vddio	  (VDD3V3),
		.vssio	  (VSS),
		.vdda	  (VDD3V3),
		.vssa	  (VSS),
		.vccd	  (VDD1V8),
		.vssd	  (VSS),
		.vdda1    (VDD3V3),
		.vdda2    (VDD3V3),
		.vssa1	  (VSS),
		.vssa2	  (VSS),
		.vccd1	  (VDD1V8),
		.vccd2	  (VDD1V8),
		.vssd1	  (VSS),
		.vssd2	  (VSS),
		.clock	  (clock),
		.gpio     (gpio),
		.mprj_io  (mprj_io),
		.flash_csb(flash_csb),
		.flash_clk(flash_clk),
		.flash_io0(flash_io0),
		.flash_io1(flash_io1),
		.resetb	  (RSTB)
	);

	spiflash #(
		.FILENAME("mem.hex")
	) spiflash (
		.csb(flash_csb),
		.clk(flash_clk),
		.io0(flash_io0),
		.io1(flash_io1),
		.io2(),			// not used
		.io3()			// not used
	);

endmodule
`default_nettype wire