| `default_nettype none | |
| /* | |
| * StriVe - A full example SoC using PicoRV32 in SkyWater s8 | |
| * | |
| * Copyright (C) 2017 Clifford Wolf <clifford@clifford.at> | |
| * Copyright (C) 2018 Tim Edwards <tim@efabless.com> | |
| * | |
| * Permission to use, copy, modify, and/or distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| * | |
| */ | |
| `timescale 1 ns / 1 ps | |
| `include "caravel.v" | |
| `include "spiflash.v" | |
| `include "tbuart.v" | |
| module uart_tb; | |
| reg clock; | |
| reg RSTB; | |
| reg power1, power2; | |
| wire gpio; | |
| wire flash_csb; | |
| wire flash_clk; | |
| wire flash_io0; | |
| wire flash_io1; | |
| wire [37:0] mprj_io; | |
| wire [15:0] checkbits; | |
| wire uart_tx; | |
| wire SDO; | |
| assign checkbits = mprj_io[31:16]; | |
| assign uart_tx = mprj_io[6]; | |
| always #12.5 clock <= (clock === 1'b0); | |
| initial begin | |
| clock = 0; | |
| end | |
| initial begin | |
| $dumpfile("uart.vcd"); | |
| $dumpvars(0, uart_tb); | |
| $display("Wait for UART o/p"); | |
| repeat (150) begin | |
| repeat (10000) @(posedge clock); | |
| // Diagnostic. . . interrupts output pattern. | |
| end | |
| $finish; | |
| end | |
| initial begin | |
| RSTB <= 1'b0; | |
| #1000; | |
| RSTB <= 1'b1; // Release reset | |
| #2000; | |
| end | |
| initial begin // Power-up sequence | |
| power1 <= 1'b0; | |
| power2 <= 1'b0; | |
| #200; | |
| power1 <= 1'b1; | |
| #200; | |
| power2 <= 1'b1; | |
| end | |
| always @(checkbits) begin | |
| if(checkbits == 16'hA000) begin | |
| $display("UART Test started"); | |
| end | |
| else if(checkbits == 16'hAB00) begin | |
| `ifdef GL | |
| $display("UART Test (GL) passed"); | |
| `else | |
| $display("UART Test (RTL) passed"); | |
| `endif | |
| $finish; | |
| end | |
| end | |
| wire VDD3V3; | |
| wire VDD1V8; | |
| wire VSS; | |
| assign VDD3V3 = power1; | |
| assign VDD1V8 = power2; | |
| assign VSS = 1'b0; | |
| assign mprj_io[3] = 1'b1; // Force CSB high. | |
| caravel uut ( | |
| .vddio (VDD3V3), | |
| .vssio (VSS), | |
| .vdda (VDD3V3), | |
| .vssa (VSS), | |
| .vccd (VDD1V8), | |
| .vssd (VSS), | |
| .vdda1 (VDD3V3), | |
| .vdda2 (VDD3V3), | |
| .vssa1 (VSS), | |
| .vssa2 (VSS), | |
| .vccd1 (VDD1V8), | |
| .vccd2 (VDD1V8), | |
| .vssd1 (VSS), | |
| .vssd2 (VSS), | |
| .clock (clock), | |
| .gpio (gpio), | |
| .mprj_io (mprj_io), | |
| .flash_csb(flash_csb), | |
| .flash_clk(flash_clk), | |
| .flash_io0(flash_io0), | |
| .flash_io1(flash_io1), | |
| .resetb (RSTB) | |
| ); | |
| spiflash #( | |
| .FILENAME("uart.hex") | |
| ) spiflash ( | |
| .csb(flash_csb), | |
| .clk(flash_clk), | |
| .io0(flash_io0), | |
| .io1(flash_io1), | |
| .io2(), // not used | |
| .io3() // not used | |
| ); | |
| // Testbench UART | |
| tbuart tbuart ( | |
| .ser_rx(uart_tx) | |
| ); | |
| endmodule | |
| `default_nettype wire |