blob: 0bbefdf508c93e25f49be13bca27da7a5a75f223 [file] [log] [blame]
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
`default_nettype none
`timescale 1 ns / 1 ps
`include "simpleuart.v"
module uart_wb_tb;
reg wb_clk_i;
reg wb_rst_i;
reg wb_stb_i;
reg wb_cyc_i;
reg wb_we_i;
reg [3:0] wb_sel_i;
reg [31:0] wb_adr_i;
reg [31:0] wb_dat_i;
wire wb_ack_o;
wire [31:0] wb_dat_o;
wire tbuart_rx;
wire ser_rx;
initial begin
wb_clk_i = 0;
wb_rst_i = 0;
wb_stb_i = 0;
wb_we_i = 0;
wb_cyc_i = 0;
wb_adr_i = 0;
wb_dat_i = 0;
wb_sel_i = 0;
end
always #1 wb_clk_i = ~wb_clk_i;
initial begin
$dumpfile("uart_wb_tb.vcd");
$dumpvars(0, uart_wb_tb);
repeat (500) begin
repeat (10000) @(posedge wb_clk_i);
end
$display("%c[1;31m",27);
$display("Monitor: Timeout, Test UART Failed");
$display("%c[0m",27);
$finish;
end
integer i;
wire [31:0] div_reg_addr = uut.BASE_ADR | uut.CLK_DIV;
wire [31:0] div_reg_data = 32'h FFFF_FFFF;
wire [31:0] dat_reg_addr = uut.BASE_ADR | uut.DATA;
wire [31:0] dat_reg_data = 32'h FFFF_FFFF;
initial begin
// Reset Operation
wb_rst_i = 1;
#2;
wb_rst_i = 0;
#2;
// Write to div register
write(div_reg_addr, div_reg_data);
#2;
read(div_reg_addr);
if (wb_dat_o !== div_reg_data) begin
$display("%c[1;31m",27);
$display("Expected %0b, but Got %0b ", div_reg_data, wb_dat_o);
$display("Monitor: Wishbone UART Failed");
$display("%c[0m",27);
$finish;
end
#6;
// Write Operation: writes to data register
write(dat_reg_addr, dat_reg_data);
#2;
read(dat_reg_addr);
if (wb_dat_o !== dat_reg_data) begin
$display("%c[1;31m",27);
$display("Expected %0b, but Got %0b ", dat_reg_data, wb_dat_o);
$display("Monitor: Wishbone UART Failed");
$display("%c[0m",27);
$finish;
end
$display("Success!");
$finish;
end
task write;
input [32:0] addr;
input [32:0] data;
begin
@(posedge wb_clk_i) begin
wb_stb_i = 1;
wb_cyc_i = 1;
wb_sel_i = 4'hF;
wb_we_i = 1;
wb_adr_i = addr;
wb_dat_i = data;
$display("Write Cycle Started.");
end
#2;
wb_we_i = 0;
// Wait for an ACK
wait(wb_ack_o == 1);
#2;
wb_cyc_i = 0;
wb_stb_i = 0;
$display("Write Cycle Ended.");
end
endtask
task read;
input [32:0] addr;
begin
@(posedge wb_clk_i) begin
wb_stb_i = 1;
wb_cyc_i = 1;
wb_we_i = 0;
wb_adr_i = addr;
$display("Read Cycle Started.");
end
// Wait for an ACK
wait(wb_ack_o == 1);
#2;
// wait(wb_ack_o == 0);
wb_cyc_i = 0;
wb_stb_i = 0;
$display("Read Cycle Ended.");
end
endtask
simpleuart_wb uut (
.wb_clk_i(wb_clk_i),
.wb_rst_i(wb_rst_i),
.wb_stb_i(wb_stb_i),
.wb_cyc_i(wb_cyc_i),
.wb_sel_i(wb_sel_i),
.wb_we_i(wb_we_i),
.wb_adr_i(wb_adr_i),
.wb_dat_i(wb_dat_i),
.wb_ack_o(wb_ack_o),
.wb_dat_o(wb_dat_o),
.ser_tx(tbuart_rx),
.ser_rx(ser_rx)
);
endmodule