| `default_nettype none |
| |
| |
| `timescale 1 ns / 1 ps |
| |
| `include "mprj_ctrl.v" |
| |
| module mprj_ctrl_tb; |
| |
| reg wb_clk_i; |
| reg wb_rst_i; |
| |
| reg wb_stb_i; |
| reg wb_cyc_i; |
| reg wb_we_i; |
| reg [3:0] wb_sel_i; |
| reg [31:0] wb_dat_i; |
| reg [31:0] wb_adr_i; |
| |
| wire wb_ack_o; |
| wire [31:0] wb_dat_o; |
| |
| initial begin |
| wb_clk_i = 0; |
| wb_rst_i = 0; |
| wb_stb_i = 0; |
| wb_cyc_i = 0; |
| wb_sel_i = 0; |
| wb_we_i = 0; |
| wb_dat_i = 0; |
| wb_adr_i = 0; |
| end |
| |
| always #1 wb_clk_i = ~wb_clk_i; |
| |
| // Mega Project Control Registers |
| wire [31:0] mprj_ctrl = uut.BASE_ADR; |
| wire [31:0] pwr_ctrl = uut.BASE_ADR + uut.IO_PADS*4; |
| |
| initial begin |
| $dumpfile("mprj_ctrl_tb.vcd"); |
| $dumpvars(0, mprj_ctrl_tb); |
| repeat (50) begin |
| repeat (1000) @(posedge wb_clk_i); |
| end |
| $display("%c[1;31m",27); |
| $display ("Monitor: Timeout, Test Mega-Project Control Failed"); |
| $display("%c[0m",27); |
| $finish; |
| end |
| |
| integer i; |
| |
| reg [31:0] data; |
| |
| initial begin |
| // Reset Operation |
| wb_rst_i = 1; |
| #2; |
| wb_rst_i = 0; |
| #2; |
| |
| for (i=0; i<uut.IO_PADS; i=i+1) begin |
| data = $urandom_range(0, 2**(7)); |
| write(mprj_ctrl+i*4, data); |
| #2; |
| read(mprj_ctrl+i*4); |
| if (wb_dat_o !== data) begin |
| $display("Monitor: R/W from IO-CTRL Failed."); |
| $finish; |
| end |
| end |
| |
| for (i=0; i<uut.PWR_CTRL; i=i+1) begin |
| data = $urandom_range(0, 2**(7)); |
| write(pwr_ctrl+i*4, data); |
| #2; |
| read(pwr_ctrl+i*4); |
| if (wb_dat_o !== data) begin |
| $display("Monitor: R/W from POWER-CTRL Failed."); |
| $finish; |
| end |
| end |
| |
| $display("Success!"); |
| $finish; |
| end |
| |
| task write; |
| input [32:0] addr; |
| input [32:0] data; |
| begin |
| @(posedge wb_clk_i) begin |
| wb_stb_i = 1; |
| wb_cyc_i = 1; |
| wb_sel_i = 4'hF; |
| wb_we_i = 1; |
| wb_adr_i = addr; |
| wb_dat_i = data; |
| $display("Write Cycle Started."); |
| end |
| // Wait for an ACK |
| wait(wb_ack_o == 1); |
| wait(wb_ack_o == 0); |
| wb_cyc_i = 0; |
| wb_stb_i = 0; |
| $display("Write Cycle Ended."); |
| end |
| endtask |
| |
| task read; |
| input [32:0] addr; |
| begin |
| @(posedge wb_clk_i) begin |
| wb_stb_i = 1; |
| wb_cyc_i = 1; |
| wb_we_i = 0; |
| wb_adr_i = addr; |
| $display("Read Cycle Started."); |
| end |
| // Wait for an ACK |
| wait(wb_ack_o == 1); |
| wait(wb_ack_o == 0); |
| wb_cyc_i = 0; |
| wb_stb_i = 0; |
| $display("Read Cycle Ended."); |
| end |
| endtask |
| |
| mprj_ctrl_wb uut( |
| .wb_clk_i(wb_clk_i), |
| .wb_rst_i(wb_rst_i), |
| .wb_stb_i(wb_stb_i), |
| .wb_cyc_i(wb_cyc_i), |
| .wb_sel_i(wb_sel_i), |
| .wb_we_i(wb_we_i), |
| .wb_dat_i(wb_dat_i), |
| .wb_adr_i(wb_adr_i), |
| .wb_ack_o(wb_ack_o), |
| .wb_dat_o(wb_dat_o) |
| ); |
| |
| endmodule |