Material Thicknesses,,,Value (um),,Variable name
field oxide (above silicon surface) ... underneath poly,,,0.07,,FOXSTEP
"min. etch and fill capability for isolation, licon, and met1",,,0.15,,DEFC
min. etch and fill capability for mcon,,,0.14,,CEFC
min. etch and fill capability for via,,,0.18,,VEFC
poly cap after SPE,,,0.2,,OVGTTH
poly thickness,,,0.18,,POLYTH
oxide spacer ,,,0.05,,SpThickn
Pre-LI ILD thickness,,,0.5,,ILDTHICKN
Licon1 etch angle (deg),,,10,,LICETANG
Standard Licon bottom CD,,,0.08,,LBCD
Mcon enclosure by Li,,,0,,mconLiEnclosure
Via1 slope,,,0.02,,Via1Slope
Oxide Bias for MM1,,,0.6,,BiasMM1
Oxide Bias for MM2,,,0.6,,BiasMM2
Oxide Bias for MM3,,,1.15,,BiasMM3
Oxide Bias for MM4,,,1.15,,BiasMM4
LI1 thickness for antenna ratio calculations,,,0.1,,LiThick
Metal 1 thickness for antenna ratio calculations (S8D*),,,0.35,,Met1Thick
Metal 2 thickness for antenna ratio calculations (S8D*),,,0.35,,Met2Thick
Inductor thickness for antenna ratio calculation (S8D*),,,4,,IndmThick
Metal 3 thickness for antenna ratio calculation  (S8Q/SP8Q),,,0.8,,Met3thick_q
Metal4 thickness for antenna ratio calculation (S8Q*/SP8Q),,,2,,Met4Thick_q
Metal 3 thickness for antenna ratio calculation  (S8P*/SP8P*),,,0.8,,Met3thick_p
Metal4 thickness for antenna ratio calculation (S8P*/SP8P*),,,0.8,,Met4Thick_p
Metal5 thickness for antenna ratio calculation (S8P*/SP8P* with 2um thick metal),,,2,,Met5Thick_p
Metal5 thickness for antenna ratio calculation (S8P*/SP8P* with 1.2um thick metal),,,1.2,,Met5Thickp_12
Metal 2 thickness for antenna ratio calculations (SP8T/S8T*),,,0.35,,Met2_Qthick
Metal 3 thickness for antenna ratio calculations (S8T* other than S8TM*),,,0.85,,Met3_Qthick
Metal 3 thickness for antenna ratio calculations (S8TM* flow),,,2,,Met3_TMthick
Metal 3 thickness for antenna ratio calculations (SP8T flow),,,0.8,,Met3_SP8Tthick
Photoresist thickness,,,1.14,,PRTHICKN
Photoresist thickness for HV Tip Implants,,,0.3,,PrThickImplant
Min width of tip implant opening,,,0.1,,minTip_impW
NTM shadowing,,,0.16,,ntmShadowing
HVNTM shadowing,,,0.232,,hvntmShadowing
HVPTM shadowing,,,0.089,,hvptmShadowing
pseudo-shadowing,,,0.045,,pseudoShadowing
Channel length for low Vt PMOS,,,0.35,,lvtpmos_poly
Width of the Low Leakage gate on each side of LowVt Pmos connected to power rails (requirement based on exp data),,,0.28,,LvtEnc_forPowerRail
CD tolerance for PDM (3s),,,1,,PdmCD_tol
Min process bias 3s tolerance,,,0.032,,PHTOL
Min process bias 3s tolerance for poly,,,0.02,,PHP1TOL
Minimum Space and Overlap,,,Value (um),,Variable name
Minimum mcon overlap onto LI for reproducible contact resistance,,,0.12,,TCONOVLP 
Dogbone PR decay length (SRS 8/4/99),,,0.2,,DBPRDEC
Bowing of rectangular contact (per edge) -- seal ring sizing,,,0.015,,TBOWINGSEAL
Waffling / Pattern Density,,,Value,,Variable name
S8 average FOM PD (extractions from logic device),,,0.45,,FOMPDAVG
Size of small PD extraction box for rough tolerance (um),,,700,,SMALLPDBOX
Size of large PD extraction box for rough tolerance (um),,,2000,,LARGEPDBOX
Min pattern density for oxide,,,0.75,,OxideMinPD
Min MM* PD range,,,0.3,,MMPDrange
FOM 700um box PD tolerance for CMP (SOI8 PCR2) for all technologies,,,0.15,,FOM700TOL
Stepping box shift as a percent of box size,,,0.5,,BOXSHIFT
Maximum metal waffle drop pattern density in the frame,,,0.55,,PD_FrameWP
Window size for frame waffle drop PD check,,,100,,WP_PDWINDOW
Step size for frame waffle drop PD check,,,10,,WP_PDSTEP
Other,,,Value,,Variable name
Poly resistor width and spacing to reduce CD variation (um),,,0.33,,POLYRCD
Poly resistor width and spacing to reduce CD variation (um),,,0.48,,POLYRSPC
Spacing between slotted_licons (Not applicable when the two edges L= 0.19um),,,0.51,,LICM1SLSP1
Precision resistor width to accommodate 6 contacts across,,,2.03,,PRECRESW
Li resistor width (to drop one Licon w/o dogbones),,,0.29,,LIRESCD
Correction factor for spacing to a wide metal line,,,2,,BIGMF
Min spacing for created dnwell to pnp.dg (more restrictive than dnwell.4 rule),,,5,,cdnwPnpSpc
"Min spacing between nwell and deep nwell on separate nets (Taken from dnwell.3 from S4* TDR *N plus rounded up, IGK request.)",,,6,,nwellDnwellSpc
Min space between deep nwells used as photo diode (um),,,5,,PDDnwSpc
Min space between dnwell (used for photo diode and other deep nwell (um),,,5.3,,PDDnwSpc1
Min/Max width of nwell inside deep nwell (for photo diodes),,,0.84,,PDNwmCD
Min/Max enclosure of nwell by deep nwell (for photo diode),,,1.08,,PDNwmDnwEnc
Min/Max width of tap inside deep nwell (for photo diode),,,0.41,,PDTapCD
Min/Max enclosure of tap by nwell inside deep nwell (for photo diode),,,0.215,,PDTapNwmEnc