###############################################################################################
# Copyright 2022 GlobalFoundries PDK Authors
#
# Licensed under the Apache License, Version 2.0 (the 'License');
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     https://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an 'AS IS' BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
################################################################################################

if FEOL

    #================================================
    #----------------P+ POLY RESISTOR----------------
    #================================================ 

    pres_poly = poly2.and(pplus).interacting(sab).interacting(res_mk).not_interacting(resistor)
    # Rule PRES.1: Minimum width of Poly2 resistor. is 0.8µm
    logger.info('Executing rule PRES.1')
    pres1_l1  = pres_poly.width(0.8.um, euclidian).polygons(0.001)
    pres1_l1.output('PRES.1', 'PRES.1 : Minimum width of Poly2 resistor. : 0.8µm')
    pres1_l1.forget 

    # Rule PRES.2: Minimum space between Poly2 resistors. is 0.4µm
    logger.info('Executing rule PRES.2')
    pres2_l1  = pres_poly.isolated(0.4.um, euclidian).polygons(0.001)
    pres2_l1.output('PRES.2', 'PRES.2 : Minimum space between Poly2 resistors. : 0.4µm')
    pres2_l1.forget 

    # Rule PRES.3: Minimum space from Poly2 resistor to COMP.
    logger.info('Executing rule PRES.3')
    pres3_l1 = pres_poly.separation(comp, 0.6.um, euclidian).polygons(0.001).or(comp.not_outside(pres_poly))
    pres3_l1.output('PRES.3', 'PRES.3 : Minimum space from Poly2 resistor to COMP.')
    pres3_l1.forget

    # Rule PRES.4: Minimum space from Poly2 resistor to unrelated Poly2. is 0.6µm
    logger.info('Executing rule PRES.4')
    pres4_l1  = pres_poly.separation(poly2.not_interacting(sab), 0.6.um, euclidian).polygons(0.001)
    pres4_l1.output('PRES.4', 'PRES.4 : Minimum space from Poly2 resistor to unrelated Poly2. : 0.6µm')
    pres4_l1.forget 

    # Rule PRES.5: Minimum Plus implant overlap of Poly2 resistor. is 0.3µm
    logger.info('Executing rule PRES.5')
    pres5_l1 = pplus.enclosing(pres_poly, 0.3.um, euclidian).polygons(0.001)
    pres5_l2 = pres_poly.not_outside(pplus).not(pplus)
    pres5_l  = pres5_l1.or(pres5_l2)
    pres5_l.output('PRES.5', 'PRES.5 : Minimum Plus implant overlap of Poly2 resistor. : 0.3µm')
    pres5_l1.forget
    pres5_l2.forget
    pres5_l.forget

    # Rule PRES.6: Minimum salicide block overlap of Poly2 resistor in width direction. is 0.3µm
    logger.info('Executing rule PRES.6')
    pres6_l1 = sab.enclosing(pres_poly,0.3.um).polygons(0.001)
    pres6_l1.output('PRES.6', 'PRES.6 : Minimum salicide block overlap of Poly2 resistor in width direction. : 0.3µm')
    pres6_l1.forget

    # Rule PRES.7: Space from salicide block to contact on Poly2 resistor.
    logger.info('Executing rule PRES.7')
    pres7_l1 = contact.inside(pres_poly).separation(sab,0.22.um).polygons(0.001).or(contact.inside(pres_poly).interacting(sab))
    pres7_l1.output('PRES.7', 'PRES.7 : Space from salicide block to contact on Poly2 resistor.')
    pres7_l1.forget

end #FEOL