(* blackbox *)
module striVe_soc (
`ifdef LVS
	inout vdd1v8,	    /* 1.8V domain */
	inout vss,
`endif
	input pll_clk,
	input ext_clk,
	input ext_clk_sel,
//	input ext_reset,
//	input reset,

	input clk,
	input resetn,
	// Main SRAM, including clk and resetn above
	// (Not used:  RAM is synthesized in this version)
	/*
	output [3:0] ram_wenb,
	output [9:0] ram_addr,
	output [31:0] ram_wdata,
	input  [31:0] ram_rdata,
	*/

	// Memory mapped I/O signals
	output [15:0] gpio_out_pad,		// Connect to out on gpio pad
	input  [15:0] gpio_in_pad,		// Connect to in on gpio pad
	output [15:0] gpio_mode0_pad,		// Connect to dm[0] on gpio pad
	output [15:0] gpio_mode1_pad,		// Connect to dm[2] on gpio pad
	output [15:0] gpio_outenb_pad,		// Connect to oe_n on gpio pad
	output [15:0] gpio_inenb_pad,		// Connect to inp_dis on gpio pad

	output 	      adc0_ena,
	output 	      adc0_convert,
	input  [9:0]  adc0_data,
	input  	      adc0_done,
	output	      adc0_clk,
	output [1:0]  adc0_inputsrc,
	output 	      adc1_ena,
	output 	      adc1_convert,
	output	      adc1_clk,
	output [1:0]  adc1_inputsrc,
	input  [9:0]  adc1_data,
	input  	      adc1_done,

	output	      dac_ena,
	output [9:0]  dac_value,

	output	      analog_out_sel,	// Analog output select (DAC or bandgap)
	output	      opamp_ena,	// Op-amp enable for analog output
	output	      opamp_bias_ena,	// Op-amp bias enable for analog output
	output	      bg_ena,		// Bandgap enable

	output	      comp_ena,
	output [1:0]  comp_ninputsrc,
	output [1:0]  comp_pinputsrc,
	output	      rcosc_ena,

	output	      overtemp_ena,
	input	      overtemp,
	input	      rcosc_in,		// RC oscillator output
	input	      xtal_in,		// crystal oscillator output
	input	      comp_in,		// comparator output
	input	      spi_sck,

	input [7:0]   spi_ro_config,
	input 	      spi_ro_xtal_ena,
	input 	      spi_ro_reg_ena,
	input 	      spi_ro_pll_dco_ena,
	input [4:0]   spi_ro_pll_div,
	input [2:0]   spi_ro_pll_sel,
	input [25:0]  spi_ro_pll_trim,

	input [11:0]  spi_ro_mfgr_id,
	input [7:0]   spi_ro_prod_id,
	input [3:0]   spi_ro_mask_rev,

	output ser_tx,
	input  ser_rx,

	// IRQ
	input  irq_pin,		// dedicated IRQ pin
	input  irq_spi,		// IRQ from standalone SPI

	// trap
	output trap,

	// Flash memory control (SPI master)
	output flash_csb,
	output flash_clk,

	output flash_csb_oeb,
	output flash_clk_oeb,

	output flash_io0_oeb,
	output flash_io1_oeb,
	output flash_io2_oeb,
	output flash_io3_oeb,

	output flash_csb_ieb,
	output flash_clk_ieb,

	output flash_io0_ieb,
	output flash_io1_ieb,
	output flash_io2_ieb,
	output flash_io3_ieb,

	output flash_io0_do,
	output flash_io1_do,
	output flash_io2_do,
	output flash_io3_do,

	input  flash_io0_di,
	input  flash_io1_di,
	input  flash_io2_di,
	input  flash_io3_di
);
endmodule